Q-See QD6505P Installation Guide download pdf (Page 4)

6 7

RS485

-B / +A

PICTURE 1-2

CONNECTING THE CONTROL MODULE

It is recommended that you test your camera near your DVR before mounting it in order to ensure that

proper connections have been made and that everything is operating normally.

STEP 1. Connect the power/video/control extension cable to the camera according to the

instructions in the camera’s manual. These are located in the section entitled “Connecting

the Camera.”

STEP 2. Connect the power and the video leads on the opposite end of the extension cable to the

power adapter and DVR or standalone monitor, respectively.

STEP 3. The bare metal control leads on the extension cable will need to connect to the orange

RS485 block on the back of the Control Module.

This block can be unplugged from the Module if needed, but care must be taken while

connecting the cables that the side with the screw heads is up to maintain proper orientation

and to avoid connecting the wrong wire to the wrong port.

Use a Phillips-head screw driver to turn

the screws counter-clockwise making

sure that the ports are open.

At least one wire will be labeled. The

white wire is the positive lead (also

referred to as RS485A or “Y”) and it

should be inserted into the left port. Use

the screwdriver to close the jaws of the

port until the wire is ﬁrmly attached.

Repeat this procedure with the negative

black (RS485B or “Z”) lead.

If you removed the orange RS485 block

during the connection, plug it back into

the Control Module at this time.

STEP 4. Plug the lead from the Control Module’s power adapter into the port on its back panel. It

is recommended that this power supply be plugged into a UL-1449 rated surge protector to

prevent damage in case of spikes of surges in power from the outlet.

IMPORTANT! We recommend connecting your camera and the Control

Module to a UL-1449 rated surge protector. It should have a joule rating of

at least 400, a response time of 10 nanoseconds or less and a clamping

voltage of no more than 330 volts.

LED READOUT

When the Control Module is powered up, it will display one of two messages - A001 or P001. The

former indicates that the camera’s control address is 1, while the latter shows that the camera is at

preset point number 1. These and other messages will be explained throughout the manual as they

appear in operational instructions, but they are collected below for your convenience.

PICTURE 1-3

Message Meaning

A001

Camera address is “1”. This address can be set (1-255) using the

DIP switches inside the camera as described in the User Manual.

If the address is changed, you will need to change the address in

the Module using the Remote Control

AUTO

Auto

Rotates the camera 360° starting and ending at the home point

CLR-

CLR

Clear. This indicates that you have cleared a setting using the

Delete button on the remote.

D=24

D represents the Pelco-D communication protocol. 24 means

2400bps communication speed. This is the default setting for your

camera. Like the address, protocol and speed are both set using

DIP switches and the Module will need to be set as well.

Home

Points camera to its preset home point.

Lt-A

Starting point for the auto pan function

Lt-B

Ending point for the auto pan function

P001

Preset point 1. You can set up to 80 points.

P=12

The camera is set to use the Pelco-P communication protocol at

1200bps

Pattern

Run

Starts the camera moving through a surveillance pattern

PstA

PSTA

The starting point of a surveillance pattern

PSt0

PST0

The ending point of a surveillance pattern

S-63

Camera movement speed is set to 63 (the fastest setting)

SEt-

Set

Saves a preset point

U018

The controller is using software Update version 18.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Q-See QD6505P Installation Guide Page 4

Comments to this Manuals

Related products and manuals for Security cameras Q-See QD6505P