Q-See QD6505P Installation Guide download pdf (Page 6)

10 11

ESC

21 3

54 6

87 9

-/--C 0

DISP

RUN

SHOT CAM

SPEED AUTO

PRESET

HOME

SETUP

PATTERN

DELETE

OPEN

IRIS

FOCUS+

FOCUS-

ZOOM+

ZOOM-

ENTER

PICTURE 2-2

It should be noted that the other buttons in that

area - the ones controlling Focus and Iris - do

not function with these cameras. This is due to

the fact that both cameras automatically focus

on a subject and the automatic iris adjusts the

level of light reaching the sensor without the

need for manual input.

Using the directional controls will override any

current automatically running operation of the

camera.

To change address

STEP 1. Press the CAM button until it shows the address number, A=001

STEP 2. If the desired channel is 1-9, simply push that number on the remote. For addresses

10-16, you will need to press the “-/--” button before entering the two digits. You may press

the C button to delete a digit.

STEP 3. If you are entering a two-digit address, you will need to press Enter after the second

digit.

When the LED dispaly is showing address information, clicking and holding Delete for three seconds

will clear all addresses.

2.2 DIRECTIONAL CONTROLS

The most basic method for controlling the PTZ camera is by using the directional controls on the

remote. The four, blue directional control buttons at the center of the remote allow you to move the

camera both left and right as well as up and down. For horizontal movement, the camera can rotate in

a full circle. Vertically, the camera only move between straight down and level.

For cameras with the zoom function, the two buttons marked Zoom+ and Zoom- allow you to mag-

nify the target area by three times.

2.3 OTHER CONTROLS

SPEED

The camera’s movement speed can be adjusted from slowest (2) to fastest (63) by two methods:

1. Shortcut buttons - These buttons are located at the bottom of the remote. S1=8, S2=40, S3=51,

S4=63

2. Pressing the Speed button and then entering the desired speed before pressing Enter.

AUTO

This will cause the camera to move to its Home Point (see next section) and begin rotating 360° until

interrupted by another command from the Remote, such as pressing a directional button.

2.4 PROGRAMMING

The camera can be programmed to store preset points in which you save a speciﬁc position -

including zoom, if applicable - for access later. In addition, you may also record a surveillance pattern

with up to 16 stops that the camera will cycle through. It is this pattern which is most commonly used

to automatically scan a wide area.

PRESET POINTS

The user is able to create up to 80 preset points which are stored in the memory of the Control

Module. The ﬁrst eight of these can be accessed with the touch of a single button at the bottom of

the remote which will cause the camera to point at the desired location. The remaining preset points

require the use of more than one button to access.

Setting a point

STEP 1. Using the directional buttons, point your camera to the desired location. Adjust the zoom

if needed/available.

STEP 2. Press and hold the Preset button for approximately 3 seconds until the Set- message

appears.

STEP 3. Enter the number for this preset.

If the number is higher than nine, you will need to press press the “-/--” button before

entering the two digits (up to 80) and then press Enter.

Home point

This is essentially Preset Point #0. This is the point that the camera will return to when you press the

Home button. It differs from the other preset points by being the starting and ending point for a 360-

degree rotation of the camera when the the Scan button is pressed. The camera will retain any zoom

settings set for the home point during its rotation.

Setting the Home point is identical to the procedure used to set any other preset point above, except

that once the Set- message appears, you should press the Home button rather than a number. The

Control Module’s LED readout will display HONE, to indicate that it has been set.

Clearing a preset point

You may overwrite a preset point by positioning the camera to a different location and then assigning

it the same number as the point you want to delete. Or, you may go to the preset point and then press

and hold the DELETE button for about three seconds until the message CLR- appears on the Control

Module.

You may clear ALL of the preset points by following the instructions for setting a preset point and

entering 95. This cannot be undone.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Q-See QD6505P Installation Guide Page 6

Comments to this Manuals

Related products and manuals for Security cameras Q-See QD6505P